Kraun KR.2W Manuale Utente

802.11g Wireless LAN ADSL2+ Router User’s Manual Version: 2.0 (January, 2007)

21.1. Features ADSL2/2+ Compliance • Support downstream rates of up to 24Mbps and upstream rates of up to 1Mbps. • Compliant to ITU-T G.992.1 (G.dm

92WAN Wide Area Network is a network that connects computers located in geographically separate areas (e.g. different buildings, cities, countries).

31.2. Minimum Requirements The following devices are necessary to configure and use the ADSL2+ Router: • A PC with Pre-installed Ethernet Adapter (R

41.4. Hardware Placement 1.4.1. Rear Panel 1) Antenna Connector The antenna connector of the router is reverse SMA connector. It allows you to con

53) Power Jack Please plug the power adapter attached with the ADSL Router to the power jack. The power adapter is 12VDC, 1A. 4) Local Area Network

62. Hardware Installation Step 1. Connect the ADSL Line Connect the router to your ADSL cable through the supplied RJ-11 telephone line. Step 2. Con

73. Setup Wizard This router provides a Setup Wizard tool for user to configure the ADSL settings. This wizard collects some ISP’s ADSL settings so t

82. The following screen will be displayed. Click “Setup Wizard”. 3. This wizard will be executed and try to search for the ADSL Router. If the AD

94. If the router cannot be found, please enter the IP Address and the Password of the router to search again. Click “Next” to continue.

105. The wizard will automatically select the country where you are in by checking the language of the operating system in your computer and skip to

113.1. Automatically Set ISP If you can find the ISP from the wizard, please follow the procedures below to let the wizard set the ISP settings auto

COPYRIGHT Copyright ©2007/2008 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored

122. Enter the Username and Password which your ISP has provided to you if it is needed. Click “Next”. 3. Click “Save” to save the settings and re

134. After saving and rebooting the router, the ISP settings are all finished. This wizard will then help to set your computer to obtain IP Address

145. The wizard will try to connect to the ISP you have selected. If the connection is failed, please run the wizard to select the ISP again. 6. I

153.2. Manually Set ISP If you cannot find the ISP from the wizard, please follow the procedures below to set the ISP settings manually. Before conf

162. Please check with your ISP the connection type of the ADSL line. Select the Connection Type and click “Next”. Note: The wizard will automatical

173. Input the VPI, VCI and Encapsulation data supplied by your ISP. If the Connection Type is “Static IP Address”, you have to input the IP Address

185. Click “Save” to save the settings and reboot the router. 6. After saving and rebooting the router, the ISP settings are all finished. This w

19 7. The wizard will try to connect to the ISP you have selected. If the connection is failed, please run the wizard to select the ISP again.

208. If you can successfully to connect to the ISP, you will see below page. If you want to configure more settings, please click “Advanced Settings

214. IP Address Setting Using the router to get into the Internet, the PCs in the network must have Ethernet adapter installed and be connected to th

Federal Communication Commission Interference Statement FCC Part 68 This equipment complies with Part 68 of the FCC Rules. On the bottom of this eq

224. In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address automatically and Obtain DNS server address automatically as s

23Windows 2000 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Double-click Net

246. Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please mak

25Windows 95/98/Me 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Double-click N

267. Check each of the tabs and verify the following settings: Bindings: Check Client for Microsoft Networks and File and printer sharing for Micros

27Windows NT 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Double-click Networ

286. Check each of the tabs and verify the following settings: IP Address: Select Obtain an IP address from a DHCP server. DNS: Let all fields are b

295. Web Management Configuration Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will automaticall

30The HOME page screen below will appear. The Home Page is divided into seven sections: Quick Start, Interface Setup, Advanced Setup, Access Manageme

31Access Management (Section 5.4) It allows you to configure ACL, IP/MAC/Application/URL Filter, SNMP, UPnP and DDNS functions. Maintenance (Sectio

this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning. This equipment may not

325.1. Quick Start The Quick Start section is designed to get you using the router as quickly as possible. Before configuring the router, please chec

33In the Quick Start, click “Run Wizard” to start the configuration.

34Please follow the steps in the setup wizard to complete the configuration of the Internet connection. Step 1: Set your new password Please enter

35Step 2: Choose your tome zone Please select the tome zone where you are located. Step 3: Set your Internet connection Please check with your ISP

36Step 4: Input the data supplied by your ISP To know more about the explanation of each setting, please refer to Section 5.2. Step 5: Re-start yo

375.2. Interface Setup 5.2.1. Internet z ATM VC Parameter Description Virtual Circuit VPI (Virtual Path Identifier) and VCI (Virtual Channel I

38Parameter Description VCI VCI is the label given to an ATM VC to identify it and determine its destination. The VCI is a 16-bit number that is in

39Parameter Description MBS MBS (Maximum Burst Size) refers to the maximum number of cells that can be sent at the peak rate. Type the MBS, which i

40z Dynamic IP Address/Static IP Address/PPPoE/PPPoA/Bridge Mode After you have selected the ISP Type, this web page will be varied depending on the

41Parameter Description TCP MSS Option The “TCP MSS Option” enables the configuration of the maximum segment size (MSS) for transient packets that

FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided betw

42Parameter Description Dynamic Route Dynamic routing allows routing tables in routers to change as the possible routes change. This router support

435.2.2. LAN z Router Local IP Parameter Description IP Address Enter the IP Address of the ADSL router for the local user to access the route

44Parameter Description Multicast Specify the method of transmitting data simultaneously to many receivers. Please select “IGMP v1” or “IGMP v2” a

45Parameter Description Lease Time In the Lease Time setting you can specify the time period that the DHCP Server lends an IP address to your LAN c

465.2.3. Wireless z Access Point Settings Parameter Description Access Point Activated or deactivated the wireless function of the router. Whe

47Parameter Description Beacon Interval The interval of time that this wireless router broadcast a beacon. Beacon is used to synchronize the wirele

48z Multiple SSIDs Settings Parameter Description SSID Index This router can support multiple SSIDs. By default, this function is disabled. You c

49z WEP/WPA-PSK/WPA2-PSK Parameter Description WEP-64Bits WEP is less level of security than WPA. WEP supports 64-bit and 128-bit key lengths to

50z Wireless MAC Address Filter Parameter Description Active This router can prevent the wireless clients from accessing the wireless network by

515.3. Advanced Setup 5.3.1. Firewall Parameter Description Firewall When you enable the firewall function, it will protect you from following a

R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL o

525.3.2. Routing z Routing Table List You can see the current routing table of the router here. If you want to add another routing rule, please c

53Parameter Description Gateway IP The next stop gateway of the path toward the destination LAN. This is the IP of the neighbor router that this ro

54z Add Route If you have another router with a LAN-to-LAN connection, you may need to create a static routing on the router that is the gateway to

55Parameter Description Announced in RIP Select “Yes”, this routing path will be propagated to other hosts through RIP broadcasts. Select “No”, thi

565.3.3. NAT 5.3.3.1. NAT Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Publi

575.3.3.2. DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP Address as the DMZ Host, all incoming

585.3.3.3. Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet ap

59Parameter Description Start Port Number Enter the start port number. End Port Number Enter the end port number. Local IP Address It is reco

605.3.4. ADSL Parameter Description ADSL Mode The default setting is “Auto Sync-Up”. This mode will automatically detect the ADSL mode including

615.4. Access Management 5.4.1. ACL If you want to restrict users from accessing certain Internet applications/services such as Internet websites, em

Contents 1. INTRODUCTION ... 1 1.1. FEATURES ...

62Parameter Description Secure IP Address The default 0.0.0.0~0.0.0.0 allows any user to use this service to remotely manage the router. Type a ran

635.4.2. Filter You can forbid some users accessing to the router by filtering the users through IP Address or MAC Address. You can also restrict som

645.4.2.1. IP/MAC Filter z IP / MAC Filter Set Editing Parameter Description IP/MAC Filter Set Index This is the item number to record the sett

65z IP / MAC Filter Rule Editing Parameter Description IP/MAC Filter Rule Index This is the item number to record the setting rule. Rule Type S

66Parameter Description MAC Address The MAC address (Media Access Control address) is a hardware address that uniquely identifies each node of a ne

675.4.2.2. Application Filter Parameter Description Application Filter Activate or deactivate the application filter. ICQ/MSN/YMSG/Real Audio/

685.4.2.3. URL Filter z URL Filter Editing Parameter Description Active Activate or deactivate the URL filter. URL Index This is the item n

695.4.3. SNMP Simple Network Management Protocol (SNMP) is a popular protocol for network management. It is used for collecting information and confi

705.4.4. UPnP When the UPnP function is enabled, the router can be detected by UPnP compliant system such as Windows XP. The router will be displayed

715.4.5. DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name fr

5.4.2.1. IP/MAC Filter ... 64 5.4.2.2. Application Filter...

72Parameter Description Password Enter the password you set for the DDNS service. Wildcard Support Enable or disable the wildcard to stand for s

735.5. Maintenance 5.5.1. Administrator Parameter Description Username The username of the router is “admin” by default. New Password Enter u

745.5.2. Time Zone The Time Zone allows your router to set its time; this will affect function such as System Log. Parameter Description Current

755.5.3. Firmware If you have new firmware for some features update, please upgrade firmware of the router here. Parameter Description Current Fi

76Parameter Description Upgrade Click “Upgrade” to begin the upgrade processes or backup file restoring processes. After the router is restarted, t

775.5.4. System Restart In this page, you can restart your router or restore to factory defaults. If you wish to restart the router using the factory

785.5.5. Diagnostics This page allows you to diagnose the connectivity of the LAN and WAN network.

795.6. Status 5.6.1. Device Info In this page, you can know the device information including firmware, MAC Address, LAN and WAN settings and also the

805.6.2. System Log Display system logs accumulated up to the present time. You can also save the logs for future reviewing.

815.6.3. Statistics Show the statistics of transmit and receive packets on the LAN port, ADSL line or WLAN port.

11. Introduction Congratulations on purchasing this 802.11g Wireless LAN ADSL2+ Router. This router is a cost-effective ADSL2+ router, with the combi

826. Troubleshooting 1. The LAN LED on the front panel does not light up. STEPS CORRECTIVE ACTION 1 Check the Ethernet cable connections between y

83The following procedures will help you to check the current IP Address setting of your computer. You can compare if your computer and router’s IP A

844. I forget my login username and/or password. STEPS CORRECTIVE ACTION 1 If you have changed the password and have now forgotten it, you will ne

856. Initialization of the ADSL connection failed. STEPS CORRECTIVE ACTION 1 Check the cable connections between the ADSL port and the wall jack.

867. Glossary 10Base-T It is an Ethernet standard for Local Area Network (LAN). 10Base-T uses a twisted pair cable with maximum length of 100 meters.

87CPE Customer Premises Equipment, such as ADSL router, USB modem. Default Gateway (Router) Every non-router IP device needs to configure a default

88FTP File Transfer Protocol. The Internet protocol (and program) used to transfer files between hosts. Idle Timeout Idle Timeout is designed so tha

89NAT Network Address Translator is defined by RFC 1631. Enable a LAN network to use one set of IP address for internal traffic. A NAT box located wh

90PPPoA (RFC 2364) The Point-to-Point Protocol (PPP) provides a standard method for transporting multi-protocol data grams over point-to-point links.

91Router A system responsible for making decisions about which of several paths network (or Internet) traffic will follow. To do this, it uses a rout